Industrial & Scientific From TEMCo Industrial on Amazon

NO TOOLS REQUIRED to change bender from ½” to ¾” – Die change from ½” to ¾” can be made in less than 1 Minute. Dies are configured to assemble so that there is no possibility to mix up sizes.

Light weight aluminum construction reduces weight to allow ease of use and movement at the job site while maintaining a quality tool producing quality repeatable bends.

High Quality, Easy to use offset bender for the professional, industrial application or the Do It Yourselfer with TEMCo’s 1 year guaranteed full refund and 5 Year Warranty

Compact design for field use on construction sites and maintenance jobs.

All metal construction built to handle tough industrial applications.

5 Year Warranty from an American name. NON-GENERIC

Includes bushings for 6awg CU/AL, 4awg CU/AL, 3awg CU, 2awg CU/AL, 1awg CU, 1/0 CU / 2/0 AL, 2/0 CU / 3/0 AL, 3/0 CU, 3/0 CU / 4/0 AL, 4/0 CU, 4/0-250MCM CU / 250MCM AL, 250MCM CU / 300MCM AL, 250-300MCM CU / 300MCM AL, 300MCM CU / 350MCM AL, 350MCM CU / 400MCM AL, 350-400MCM CU / 400MCM AL, 350-400MCM CU, 500MCM AL, 500MCM CU, 500MCM CU / 600MCM AL, 500-600MCM CU / 600MCM AL, 600MCM CU, 600MCM CU / 700MCM AL, 600-700MCM CU / 750MCM AL, 700MCM CU, 750MCM CU / 900MCM AL

Each die has adjustable depth for changing insulation thickness

Stripper can be adjusted to strip lengths up to 4” depending upon application.

Nominal OD: 0.303", Conductor stranding: 260/30

Resistant to Cuts, Tears, Abrasion, Water, Oil, Grease and Flame.

NEC article 630 electric welders, Meets SAE J1127 and ASTM B-172 standards. RoHS Compliant.

Machined Cylinder Housing improves the quality of the jack - Compare to traditional stamped sheet metal cylinder housing.

Over Travel Protection eliminates damage to internals from over-extension of piston.

Hard Chrome Ram resists corrosion and maximizes seal wear life. 5 Year Warranty.

Punching Thickness Capacity: 1/8 inch (11 ga) Steel Punching Capacity, 1/16 inch Stainless Steel.

Punches: Steel, Stainless Steel, Brass, Copper, Aluminum (soft alloys only), Fiberglass, Plastic

5 Year Warranty from a well-known American name. NON-GENERIC

Housed in a rugged phenolic resin case. PCB free

1/4 in. Quick Disconnect Terminals

Designed specifically for use with OEM single phase motor and gear motor applications. No hassle 5 Year Warranty.

12" Steel Handles with Rubber Grips

NOTE: Will not cut 4/0 MTW or similar diameter wire.

Perfect for Battery & Welder Cables, Building Wiring, SO Cord and more. 5 Year Warranty

Slug splitting designed dies for easy slug removal that leaves a round hole with clean edges and a uniform size is provided on punch sizes ½", ¾", 1", 1¼", 1 ½" & 2"

Deep Draw dies that are designed with an optimized angle on the cutter face that requires less force to make the cut, reducing operator and tool fatigue is provided on punch sizes 2 ½",3", 3 ½" & 4"

Punching Thickness Capacity: 1/8 inch (11 ga) Steel, 1/16 inch Stainless Steel Punches: Steel, Stainless Steel, Brass, Copper, Aluminum (soft alloys only), Fiberglass and Plastic

Slug splitting design on punches allows for easier slug removal – the smooth operation leaves the round hole with clean edges and a uniform size. Manual punch works for use in tight areas.

Kit comes in a rugged storage case. Storage case is designed with a secure-closing lid for keeping all the pieces neatly organized for easy transport.

Draw Stud threads are compatible with THA001 and THA013 draw studs, allowing for use on TEMCo hydraulic drivers TH0004 and TH0037 or equivalent.